Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Irving
Gate access control in Irving typically runs between $400 and $2,800 installed, depending on whether you’re adding a keypad to an existing opener, running a new power line to a detached gate, or installing a full phone-entry system with a video intercom. Most repairs on keypads, card readers, and receiver boards are done in a single visit, and we quote the full price before any work starts. If your gate won’t open from the keypad but the remote still works, or the gate reverses after rain, you’re dealing with issues we see regularly across Irving’s neighborhoods. Call (936) 259-0479 and a live person will answer, any hour, any day.
Why Ironworks Gate Co. Is Irving’s Preferred Gate Access Control Company
We’ve been running gate crews in and around Irving long enough to know that this city’s housing stock is not all the same. Homes in Valley Ranch built in the 1990s have different gate setups than the newer infill construction off MacArthur Boulevard, and the townhome communities near Irving Boulevard and in Las Colinas tend to share lot lines and gate posts in ways that demand a different measurement discipline. Our Gate Access Control team works all of these areas every month, so we know which operators are common where, and we carry common parts on the truck so a first visit is usually the last visit.
The homeowners we serve in Irving have told us the same thing for years: they’re done with guessing. They want a written number, a tidy install or repair, and a gate that works when they punch the code. That’s how we work. Victor Salinas set that standard when he started leading the company, and it hasn’t changed since. Uniformed, background-checked technicians, a written 90-Day Done Right Promise on every job, and an honest price settled before we turn the first bolt.
We’re not a handyman service that happens to touch gates. We only do gates: Gate Repair in Irving, installations, motors, keypads, welding, photo eyes, safety edges, and full access control systems. If the gate won’t open, we’ll find out why and tell you what it’ll cost before you commit. Most Irving jobs are completed the same day we arrive.
Our Gate Access Control Services in Irving
Keypad Entry
A keypad is the most common way our Irving customers control their gates. Whether it’s a wired keypad on a post near the driveway or a wireless unit mounted on a stone column, the two things that matter most are the weather sealing and how the wire was buried. In Irving’s compacted clay, shallow conduits shift and wire splices fail more often than the keypad itself. We sleeve low-voltage runs, seal the back-box, and test the relay output before we leave. A typical keypad install in Irving runs $400 to $900, including the keypad, wiring, and programming.
Remote Control
Remotes are straightforward, but adding a remote to an existing Irving gate often means the receiver is older than the homeowner thinks. We stock and service receivers and remotes for FAAC, BFT, Linear, Viking, and the other major brands, so we can match a new remote to an old board without replacing the whole operator. If your remote opens the gate but the keypad won’t, the problem is usually the keypad wiring or a loop detector fault, not the remote.
Phone Entry
Phone entry is growing fast in Irving, especially in the gated communities along North MacArthur and around the HEB area, where homeowners want visitors to call from the pedestal and get buzzed in from anywhere. A phone entry add-on runs $900 to $1,800 in Irving, depending on the intercom panel, the SIM or ethernet path, and whether we’re pulling a new low-voltage line from the operator. We install the panel, tie it into the existing operator, and program the owner’s phone line or app before we leave.
Card Reader
Card readers make sense where several people need entry: family, housekeepers, pool services. In Irving, we install standalone Wiegand readers and tie them into existing gate boards. A card reader install in Irving runs $500 to $1,200, including reader, cards, wiring, and programming. The most common mistake we fix is a reader that was wired to a constant power source that drained the operator battery, so we always check load draw first.
We also handle the full Gate Access Control in Irving scope: video intercoms, smart access via phone app, safety edges, loop detectors, and full control board replacements.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Irving
We’re trained and equipped on nine gate-automation brands, including FAAC, BFT, and Linear, which cover most of what’s installed across Irving’s older subdivisions and newer infill lots, and we service Gate Motor & Opener - Irving units from all of them. We warranty our work for 90 days in writing, and we stock common boards, remotes, and photo eyes locally so a repair in Irving doesn’t wait on a part two states away. If your operator is a Viking or something else, tell us what it’s doing when you call. Nine times out of ten we can tell you over the phone what you’re likely dealing with.
Common Gate Access Control Problems We See in Irving Homes
- The gate reverses for no reason after rain. Irving’s compacted clay soil expands with moisture and shrinks in dry heat. A loop detector buried in that soil reads false changes and cancels the open command, so the gate starts, reverses, and starts again. The fix is a loop re-tune or a re-bury at the correct depth, not a new board.
- The keypad stopped working but the remote still opens the gate. That’s almost always a broken low-voltage wire or a corroded splice where the conduit shifted. We trace the run, replace the damaged section, and seal the junction properly.
- The gate post wobbles after a storm. Shallow post footings in Irving clay heave and settle, pulling the operator arm out of alignment and stripping the rack and pinion. We core out and re-set the hinge post on a correct footing depth, then re-hang the gate and re-test travel.
- Solar openers losing power to the keypad and card reader. In Irving’s denser townhome areas, solar panels don’t get enough direct sun between buildings, especially in winter overcasts. The opener still has mechanical travel, but the access control board browns out mid-cycle. In those cases we recommend a hardwired transformer or a properly sized battery reserve.
Pricing for Gate Access Control in Irving, TX
For Irving homeowners, here’s what you should expect to pay. A wired keypad installation runs $400 to $900. Adding a phone entry system runs $900 to $1,800 with the panel and wiring. A card reader install runs $500 to $1,200 with cards included. A full new operator with access control (keypad, photo eyes, remote receiver) lands between $2,200 and $5,500 depending on gate size and brand. A loop detector repair or replacement runs $300 to $600.
What changes the price is the run length for low-voltage wire, whether the post is set correctly already, and whether the operator is in good enough shape to accept a new access control board. We quote the full price before work begins, and that price doesn’t change unless we find something you approve in writing. Estimates are free. Call (936) 259-0479 and we’ll give you a real number for your gate.
We Also Serve Cities Near Irving
Our crews run routes through the west side of the metroplex every week, and we schedule service in Dallas, Addison, Coppell, and Carrollton on the same days we’re in Irving, so drive time doesn’t inflate your bill. If you’re a few minutes across the city line, we’ll still give you an honest quote and a real arrival window.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Irving
Because the loop detector buried in your driveway is reading moisture-driven soil movement as a vehicle. Irving’s clay soil expands when it rains and the detector’s sensitivity drifts, so the gate starts to open, thinks the path is blocked, and reverses. We re-tune or re-bury the loop at the correct depth, and the phantom reversal stops. Call (936) 259-0479 if it’s happening at your place.
In most cases, yes. If your existing operator has a functioning control board and a dry lower enclosure, we can wire in a phone entry panel and program it to open the gate from an app or phone line. You don’t need a new operator just to get phone entry. We’ll confirm compatibility on-site before you spend anything.
For Irving’s expansive clay, we set gate posts at least 36 inches deep with a wider concrete base than you’d use in rockier soil. The key isn’t just depth, it’s mass and drainage. If the post sits in a pocket that holds water, it’ll heave no matter how deep it is. We also angle the post slightly away from the gate’s resting weight so the gate hangs square over time.
We don’t see one brand fail more than others. We see the same brand fail twice: once when it was installed wrong, and again when the soil conditions weren’t accounted for. Most of what we repair in Irving is not operator failure, it’s mounting and wiring failure. That’s why we train on nine brands and test the full circuit after every install.
Because the remote receiver and the keypad run on separate signals. The remote talks to the receiver by radio, but the keypad sends a hard-wired relay signal through buried low-voltage wiring. A broken or corroded wire shuts down the keypad while the remote keeps working. We find the break and repull that section. Call (936) 259-0479 for an exact diagnosis.
In the Valley Ranch neighborhood, our crew replaced a DoorKing slide gate operator where the loop detector was misreading shifting clay, causing the gate to reverse mid-travel. We poured a new post footing, re-buried the loop at 1.5 inches, and re-tested safety photocells under UL 325 before handing over the remote programming. That’s the kind of fix that separates a one-visit job from a recurring headache.
Call (936) 259-0479 for a free estimate on any gate access control work in Irving. A real person answers, day or night.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Irving since 1984.